|
SolidSwitch 104
|
|
VE.Bus Smart dongleThe VE.Bus Smart dongle is two products in one:
First of all it is the Bluetooth accessory for our range of inverter/chargers: Multis, MultiPlusses, MultiPlus-II, MultiGrid, MultiGrid-II, Quattros, and our series of Phoenix Inverters with a VE.Bus port. When installed, use the VictronConnect App to monitor operation and also operate the system: change the input current limit as well as switch between Off, On and Charger-only modes. Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models. For monitoring, the device is a great alternative in caravans, smaller yachts and motor homes for which the Color Control GX or Venus GX are a step too far. |
|
GX Touch Wall MountThe GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.
Models:5" & 7" |
|
Smart Battery SenseSmart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers.
With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life. |
|
GX LTE 4GThe GX LTE 4G is a cellular modem for the GX range of monitoring products. It provides a mobile internet connection for the system and connection to the VRM Portal. It works on 2G, 3G and 4G networks.
There are multiple models, refer to the manual to see which model best matches the available cellular network bands in your area. The GX LTE includes a built-in GPS receiver. When the optional GPS antenna is installed, the system can be tracked as well as Geo-fenced on the VRM Portal. |
|
Wall mount enclosure for BMV or MPPT ControlEasily mount a BMV-700 series or MPPT Control on a wall.
|
|
Battery BalancerThe Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries. When the charge voltage of a 24V battery system increases to more than 27V, the Battery Balancer will turn on and compare the voltage over the two series connected batteries. The Battery Balancer will draw a current of up to 1A from the battery (or parallel connected batteries) with the highest voltage. The resulting charge current differential will ensure that all batteries will converge to the same state of charge.If needed, several balancers can be paralleled.
A 48V battery bank can be balanced with three Battery Balancers. |
|
MPPT WireBox - TrThe MPPT WireBox provides an extra level of safety, and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.
There are various sizes available: MPPT WireBox-S 75-10/15 MPPT WireBox-S 100-15 MPPT WireBox-S 100-20 MPPT Wirebox-M 100-30/50 & 150/35/45 MPPT WireBox-L Tr 150-60/70 & 250-60/70 MPPT WireBox-XL Tr 150-85/100 & 250-85/100 MPPT WireBox-XL Tr 150-85/100 & 250-85/100 VE.Can |
|
MPPT WireBox - MC4
The MPPT WireBox provides an extra level of safety, and is particularly useful if your MPPT Solar Charger is installed in a general access area. It covers all DC terminals, preventing accidental or inquisitive contact with terminal screws.
There are various sizes available: MPPT WireBox-L MC4 150-45/60/70 & 250-60/70 MPPT WireBox-L MC4 150/70 & 250/70 VE.Can MPPT WireBox-XL MC4 150-85/100 & 250-85/100 MPPT WireBox-XL MC4 150-85/100 & 250-85/100 VE.Can |
|
AC Current sensor - single phase - max 40AThe AC Current sensor is a simple external current sensor used to measure AC Current, Power (VA) and calculate energy of a PV Inverter connected to the AC input or output of a Multi or Quattro. These values can then be displayed and sent to the VRM-website by the Color Control. The two measurement wires can be connected to the AUX and/or temperature sense input of a Multi or Quattro.
|
|
Current Transformer for MultiPlus-IICurrent Transformer 100A:50mA for MultiPlus-II / MultiGrid-II to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing. See MultiPlus-II datasheet for more details.
|
|
Energy Meters ET112, ET340 & EM24The ET112 (for single phase max. 100A) and the ET340 (for three phase max. 65A) Energy Meters are typically used in an Energy Storage System.
The EM24 is for 3 phase monitoring only. There is a EM24 meter model for RS485 connection and one that connects over Ethernet. All ET models connect via RS485. To measure the power and energy of the whole application at the distribution box. Or to measure the output of a PV Inverter, to display the data on the Color Control GX and the VRM Portal. |
|
Zigbee to USB converter & Zigbee to RS485
This pair of Zigbee converters is to wirelessly connect an Energy Meter to a GX Device.
Zigbee to USB converter, DRF2658C, DTK Zigbee to RS485 converter, DRF2659C, DTK |
|
Anti-Islanding Box 63A single and three phaseThe Anti-Islanding Box 63A single and three phase is a combination of an anti-islanding device, the Ziehl UFR1001E, two in-line contactors and main circuit breaker. It is suitable for both single phase or 3 phase systems. It is rated up to 63A per phase and all parts are conveniently housed in an IP65 rated enclosure.
The Anti-Islanding Box can be added to a grid-feeding inverter/charger system (ESS) to meet local anti-islanding regulations. Note that Ziehl UFR1001E is also available as a separate product. |
|
M6/M8 eyelet connector with fuseThe M6/M8 eyelet connector with fuse is an accessory for the Blue Smart IP65 Charger with DC connector.
|
|
Clamp connector with fuseThe clamp connector with fuse is an accessory for the Blue Smart IP65 Chargers.
|
|
2 meter extension cableThe 2 meter extension cable is an accessory of the Blue Smart IP65 Charger with DC connector.
|
|
12V cigarette lighter plug with fuseThe 12V cigarette lighter plug, with fuse, is an accessory for the Blue Smart IP65 Charger with DC connector. With this plug you can charge your vehicle battery via the cigarette lighter socket.
|
|
Battery indicator panel
Battery State of Charge (SOC)
The battery indicator panel shows the state of charge of the battery. It is an accessory for the Blue Smart IP65 Chargers. Suitable for 12V lead acid batteries (flooded, GEL, AGM) |
|
Battery Indicator Eyelet M8The Battery Indicator Eyelet M8 is an accessory for the Blue Smart IP65 Chargers.
|
|
Rubber bumper for IP65 ChargerThe IP65 Charger is already protected against dust, and water spray - now you can protect it from accidental damage too. This rubber bumper allows it to withstand the knocks and bangs of workshop life. It will extend the life of your charger, and it has an easy-carry handle, ...or hang it from a hook when not in use.
There are two sizes available: Blue Smart IP65 Charger 12/10, 12/15 & 24/8 Blue Smart IP65 Charger 12/25 & 24/13 |
|
Carry Case for Blue Smart IP65
|
|
Ziehl Voltage and frequency relay UFR1001E
The UFR1001E monitors voltage and frequency in plants for own generation of electricity. It fulfills the requirements of VDE-AR-N 4105 bdew-directive, G59/3, G83/2 and ÖVE/ÖNORM E 8001-4-712:2009 for generators connected to the public grid. For more information, we refer you to the datasheet and certificates below which are available to download. Or visit www.ziehl.de and look for the UFR1001E under the Mains monitoring group.
Note that Victron also stock a pre-built box including the Ziehl UFR1001E, two in-line 63A contactors and a main circuit breaker: the Anti-Islanding Box 63A single and three phase. |
|
VE.Direct Bluetooth Smart dongleUsing the VE.Direct to Bluetooth Smart dongle you can display your BMV or MPPT information on iOS and Android devices, using the VictronConnect App. View information wirelessly such as battery status and solar panel power, plus other useful data. The dongle is able to read data from all products with a VE.Direct port, such as the BMV-70x series battery monitors, Phoenix Inverters with VE.Direct port, MPPT Solar Charge Controllers.
|
|
VE.Direct to USB interface
The VE.Direct to USB interface connects products with a VE.Direct connection to devices with a USB port, for example a computer. With this cable it is also possible to connect more than two VE.Direct products to a single CCGX.
|
|
VE.Direct TX digital output cable
The VE.Direct TX digital output cable can be used in combination with the BlueSolar and SmartSolar MPPT chargers. It supports the following applications:
- Solar lighting applications - Virtual load output |
|
Temperature sensor Quattro, MultiPlus and GX DeviceTemperature sensor for Quattro, MultiPlus and GX Device.
|
|
VE.Direct to global remote interface
|
|
Victron Global Remote to VE.Direct Connection Kit |
|
VE.Direct to RS232 interface |
|
RS232 to USB converter |
|
Interface MK3-USB
The MK3-USB allows the following products to connect to a computer for configuration and firmware updates:
Multi, MultiGrid, MultiPlus, MultiPlus-II, Quattro, Inverter/Charger settings in ECOmulti, EasySolar, EasyPlus, and Inverters with a VE.Bus communication port. |
|
VE.Can Power Cable
When the CAN bus is not powered by a Skylla-I or an MPPT, you will need the new VE.Can Power Cable to supply the power.
|
|
VE.Can RJ45 terminatorThe VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.
|
|
VE.Can resistive tank sender adapterThe VE.Can resistive tank sender adapter allows a standard resistive tank level sender to connect to the Color Control GX. It is compatible with both European standard 0-180 Ohm and United States standard 240-30 Ohm tank level senders and is accurate to ±1%. It is easily configurable to resistive senders from fuel, fresh water, waste water, well water, oil and black water (sewage) tanks. It supports up to 16 tanks of each type. The unit is a simple setup with two small rotary switches and it gets its power from the VE.Can network.When you use a Skylla-i or a MPPT with CAN bus in the system, the power to the CAN bus will be supplied by either one of them. When the CAN bus is not powered by a Skylla-I or a MPPT, you will need the new VE.Can Power Cable to supply the power.
|
|
Shunt |
|
CANUSB interfaceThe CANUSB interface is used to connect a VE.Can product to a computer.
|
|
VE.Direct non inverting remote on/off cableUse this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models.
Note that it's not necessary to use this cable on the larger SmartSolar models, as they feature an onboard Remote On/Off terminal. The charger will be enabled when the signal on the cable is high. The charger is disabled when the source signal is pulled low or left free floating. Note that when using this cable, it's not possible to use the VE.Direct port for any other purpose. Such as connecting to a GX device, or for example a VE.Direct Bluetooth Smart dongle on a BlueSolar charger. |
|
Temperature Sensor for BlueSolar PWM-ProTemperature Sensor for BlueSolar PWM-Pro
|
|
Inverting remote on-off cableUse this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output:
|
|
RS485 to USB interfaceRS485 to USB interface, available in 1.8 m and 5 m
|