DC-DC Converters & Chargers  

Orion-Tr DC-DC Converters Isolated

Remote on/off
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on/off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel.
IP43 protection
When installed with the screw terminals oriented downwards. 
Screw terminals
No special tools needed for installation.
Input fuse
On 12V and 24V input models only.

Models:12 / 24 / 48 Volt

Orion-Tr DC-DC Converters Non-isolated

High efficiency
Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection
When installed with the screw terminals oriented downwards. 
Screw terminals
No special tools needed for installation.
Models:24 Volt

Orion-Tr Smart DC-DC Charger Isolated

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.
For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.
The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.
Suitable for high temperatures up to 55°C with a full rated output up to 40°C.

Orion DC-DC Converters Non-isolated, High power

Remote on/off connector
The remote on/off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger
For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. 
All models with adjustable output can be paralleled to increase output current
Up to five units can be connected in parallel.
Models:12 / 24 Volt

Orion DC-DC Converters 110V, Isolated

Models:12 / 24 Volt

​Orion IP67 24/12 and 12/24 DC-DC Converters

Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. 
Available in 5 models
Orion IP67 24/12-5
Orion IP67 24/12-10
Orion IP67 24/12-20
Orion IP67 24/12-100
Orion IP67 12/24-50

Models:12 / 24 Volt

Buck-Boost DC-DC Converter 25A / 50A / 100A

DC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. The Buck-Boost DC-DC Converter is a DC-DC converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Since, when the engine is running, these dynamos (powered by the on-board electronics of Euro 5 and 6 engines) do not always emit the correct charging current, a DC-DC converter is essential for charging the service battery properly.

DC Distribution systems & Fuses

Lynx Smart BMS

The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature rich and complete option. Its main features are:
  • Built-in 500A contactor used as a fallback safety mechanism and also suitable as a remote controllable main system switch.
  • Battery monitor, indicating state of charge percentage and more data.
  • Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell.
  • Bluetooth for use with the VictronConnect App, for setup and monitoring.
  • Local and remote monitoring using a Victron GX device, for example The Cerbo GX  .
The Lynx Smart BMS is part of the modular Lynx Distribution system.

Lynx Distributor

A modular DC busbar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. Part of the modular Lynx distribution system.

Lynx Shunt VE.Can

The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse (not included), the built-in battery monitor accurately monitors the state of charge of your battery. Use a GX device (e.g. Cerbo GX) for reading out the information. Part of the modular Lynx distribution system.

Lynx Power In​

A modular DC busbar, used to connect batteries to the Lynx DC distribution system.

Busbars 150, 250 & 600 Amps

Busbars are used for high current distribution and at the same time they provide connections for batteries and/or DC equipment.
We offer a number of busbars with different current ratings, and a different number of connection terminals. Each busbar is fitted out with a removable protection cover. 
Available models:
150A / 70V - 4 high current connections
150A / 70V - 6 high current connections
150A / 70A - 2P with 10 screws +cover
150A / 70A - 2P with 20 screws +cover
250A / 70V - 4 high current connections
250A / 70V - 6 high current connections
250A / 70A - 2P with 6 screws +cover
250A / 70A - 2P with 12 screws +cover
600A / 70V - 4 high current connections and 8 low current connections
600A / 70V - 8 high current connections and 8 low current connections 

Fuses & fuse holders

Besides an assortment of ANL, MIDI and MEGA fuses, Victron features three different types of fuse holders:
  • Simple single fuse holders for each of above fuse types.
  • A six-way fuse holder, MEGA fuses only.
  • Modular single fuse holders, for MEGA fuses only. With an optional busbar accessory to efficiently connect multiple fuses together. 
Besides above fuse holders, Victron also have the Lynx Power In and the Lynx Distributor, part of the Lynx 1000 Amp distribution system.

    Interested in Solar? Drop us a message for a free quote or advice...