Battery Monitors, Isolators, Combiners, Converters & DC Distribution
Battery Monitors
BMV-700 SeriesThe BMV-700 is our newest high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery.
![]()
![]()
|
BMV-712 SmartWith Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance.
![]()
|
Battery BalancerThe Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries.When the charge voltage of a 24V battery system increases to more than 27V, the Battery Balancer will turn on and compare the voltage over the two series connected batteries. The Battery Balancer will draw a current of up to 1A from the battery (or parallel connected batteries) with the highest voltage. The resulting charge current differential will ensure that all batteries will converge to the same state of charge.If needed, several balancers can be paralleled. A 48V battery bank can be balanced with three Battery Balancers.
![]()
|
VE.Net Battery Controller
The VE.Net Battery Controller (VBC) is a device that monitors your battery status. It constantly measures the battery voltage, battery current, and battery temperature, and uses this information to calculate the state of charge of your battery.
![]()
![]()
|
Lynx Ion BMSThe Lynx Ion BMS is the Battery Management System that goes with the Lithium HE batteries and our Lithium 24V batteries. It has a built-in safety disconnect switch, and manages cell-balancing, battery balancing and charging and discharging of the system. The Lynx Ion BMS protects the battery pack from both overcharging and depletion.
![]()
|
Lynx ShuntVE.Net Version:
The Lynx Shunt VE.Net is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge on your battery. Use the Blue Power Panel or VE.Net panel for reading out the information. Part of the modular Lynx distribution system. VE.Can Version: The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge of your battery. Use the Color Control GX for reading out the information. Part of the modular Lynx distribution system. |
Lynx Ion + Shunt 350/600The Lynx Ion is the Battery Management System (BMS) that controls the 24V/180Ah Lithium Ion batteries. It contains the 350A safety contactor, and controls the cell-balancing, charging and discharging of the system. The Lynx Ion will protect the battery pack from both overcharging and depletion.
![]()
|
Battery Isolators & Combiners
Argo Diode Battery IsolatorsDiode Battery Isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. Low voltage drop due to the use of high efficiency Schottky diodes.
![]()
|
Argo FET Battery Isolators
Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents.
![]()
|
Argo Diode Battery Combiners
Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load.
![]()
|
Cyrix-i Battery Combiner Kit
This Battery Combiner Kit is for adding a 2nd or 3rd battery system in your car, boat, RV or any other vehicle. It utilizes the simplest and most advanced technology to keep all your batteries charged using the engine’s electrical system, but isolates the starting battery when charging ceases so you never get stranded.
![]()
|
Cyrix Battery CombinersThe Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased.
Models:120A / 230A / 400A ![]()
![]()
![]()
![]()
|
Battery Isolators & Combiners
BatteryProtectThe BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
![]()
![]()
|
DC-DC Converters
Orion-Tr DC-DC Converters IsolatedRemote on-off: The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).
Adjustable output voltage: can also be used as a battery charger. For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current. An unlimited number of units can be connected in parallel. IP43 protection: When installed with the screw terminals oriented downwards. Screw terminals: No special tools needed for installation. Input fuse: On 12V and 24V input models only. Models: 12 / 24 / 48 Volt ![]()
|
Orion-Tr DC-DC Converters Non-isolatedHigh efficiency
Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection When installed with the screw terminals oriented downwards. Screw terminals No special tools needed for installation. Models:24 Volt ![]()
|
Orion DC-DC Converters Non-isolated, High powerRemote on-off connector
The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by the engine run/stop switch (see manual). All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models with adjustable output can be paralleled to increase output current Up to five units can be connected in parallel. Models:12 / 24 Volt ![]()
|
Orion DC-DC Converters Isolated, 360W and special purpose modelsModels: 12 / 24 / 48 / 100 Volt
![]()
|
Orion IP67 24/12 DC-DC Converters
Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. Available in 3 models Orion IP67 24/12-5 Orion IP67 24/12-10 Orion IP67 24/12-20 Models:24 Volt ![]()
|
Buck-Boost DC-DC Converter 25A and 50ADC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. The 50A Buck-Boost DC-DC Converter is a DC-DC converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Since, when the engine is running, these dynamos (powered by the on-board electronics of Euro 5 and 6 engines) do not always emit the correct charging current, a DC-DC converter is essential for charging the service battery properly.
![]()
|
DC Distribution Systems
Lynx Ion BMSThe Lynx Ion BMS is the Battery Management System that goes with the Lithium HE batteries and our Lithium 24V batteries. It has a built-in safety disconnect switch, and manages cell-balancing, battery balancing and charging and discharging of the system. The Lynx Ion BMS protects the battery pack from both overcharging and depletion.
![]()
|
Lynx Shunt VE.NetThe Lynx Shunt VE.Net is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge on your battery. Use the Blue Power Panel or VE.Net panel for reading out the information. Part of the modular Lynx distribution system.
Lynx Shunt VE.Can
The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge of your battery. Use the Color Control GX for reading out the information. Part of the modular Lynx distribution system.
|
Lynx Ion + Shunt 350/600
The Lynx Ion is the Battery Management System (BMS) that controls the 24V/180Ah Lithium Ion batteries. It contains the 350A safety contactor, and controls the cell-balancing, charging and discharging of the system. The Lynx Ion will protect the battery pack from both overcharging and depletion.
![]()
|
ESP DC Link BoxThe DC Link Box brings all the primary DC protection, DC monitoring and sensor connections into one simple to fit enclosure. It includes:
- 4 Mega fuses (2x 300A, 1x 200A, 1x 100A) and 1 Midi fuse (60A). These can be changed to suit the user's requirements. Mega fuses are available in sizes from 100 to 500 amps and Midi fuses from 30 to 125 amps. - 500 Amp shunt. - Test button with LEDs for all 5 fuses and a polarity warning LED. - Fused connection points for MultiPlus voltage sense and BMV-600 connections. - Fused connections for magnetically latching battery isolator which can be controlled via ESP system panel. - RJ 11 and 45 socket connections for ESP system panel. ![]()
|